Your development team has a full backlog? No time for infrastructure architecture? Our DevOps team is ready to support you! Show
To create a linear gradient you must define at least two color stops. Color stops are the colors you want to render smooth transitions among. You can also set a starting point and a direction (or an angle) along with the gradient effect. Syntaxbackground-image: linear-gradient(direction, color-stop1, color-stop2, ...); Direction - Top to Bottom (this is default) The following example shows a linear gradient that starts from the left. It starts fully transparent, transitioning to full color red: The 2 CSS function creates an image consisting of a progressive transition between two or more colors along a straight line. Its result is an object of the 3 data type, which is a special kind of 4.
5The position of the gradient line's starting point. If specified, it consists of the word 6 and up to two keywords: one indicates the horizontal side ( 7 or 8), and the other the vertical side ( 9 or 0). The order of the side keywords does not matter. If unspecified, it defaults to 1.The values 2, 1, 4, and 5 are equivalent to the angles 6, 7, 8, and 9, respectively. The other values are translated into an angle. 0The gradient line's angle of direction. A value of 6 is equivalent to 2; increasing values rotate clockwise from there. 3A color-stop's 4 value, followed by one or two optional stop positions, (each being either a 5 or a 6 along the gradient's axis). 7An interpolation hint defining how the gradient progresses between adjacent color stops. The length defines at which point between two color stops the gradient color should reach the midpoint of the color transition. If omitted, the midpoint of the color transition is the midpoint between two color stops. Note: Rendering of follows the same rules as color stops in SVG gradients. Note also that the first example above does not exactly render as depicted in Mozilla Firefox (particularly version 80.0b3). You'll have to set the html height property to 100% or 100vh to render as depicted. As with any gradient, a linear gradient has ; i.e., it has no natural or preferred size, nor a preferred ratio. Its concrete size will match the size of the element it applies to. To create a linear gradient that repeats so as to fill its container, use the 8 function instead.Because 3s belong to the 4 data type, they can only be used where 4s can be used. For this reason, 2 won't work on 3 and other properties that use the 4 data type.A linear gradient is defined by an axis—the gradient line—and two or more color-stop points. Each point on the axis is a distinct color; to create a smooth gradient, the 2 function draws a series of colored lines perpendicular to the gradient line, each one matching the color of the point where it intersects the gradient line.The gradient line is defined by the center of the box containing the gradient image and by an angle. The colors of the gradient are determined by two or more points: the starting point, the ending point, and, in between, optional color-stop points. The starting point is the location on the gradient line where the first color begins. The ending point is the point where the last color ends. Each of these two points is defined by the intersection of the gradient line with a perpendicular line passing from the box corner which is in the same quadrant. The ending point can be understood as the symmetrical point of the starting point. These somewhat complex definitions lead to an interesting effect sometimes called magic corners: the corners nearest to the starting and ending points have the same color as their respective starting or ending points. Customizing GradientsBy adding more color-stop points on the gradient line, you can create a highly customized transition between multiple colors. A color-stop's position can be explicitly defined by using a 6 or a 5. If you don't specify the location of a color, it is placed halfway between the one that precedes it and the one that follows it. The following two gradients are equivalent.
By default, colors transition smoothly from the color at one color stop to the color at the subsequent color stop, with the midpoint between the colors being the half way point between the color transition. You can move this midpoint to any position between two color stops by adding an unlabelled % color hint between the two colors to indicate where the middle of the color transition should be. The following example is solid red from the start to the 10% mark and solid blue from 90% to the end. Between 10% and 90% the color transitions from red to blue, however the midpoint of the transition is at the 30% mark rather than 50% as would have happened without the 30% color hint.
If two or more color stops are at the same location, the transition will be a hard line between the first and last colors declared at that location. Color stops should be listed in ascending order. Subsequent color stops of lower value will override the value of the previous color stop creating a hard transition. The following changes from red to yellow at the 40% mark, and then transitions from yellow to blue over 25% of the gradient
Multi-position color stop are allowed. A color can be declared as two adjacent color stops by including both positions in the CSS declaration. The following three gradients are equivalent:
By default, if there is no color with a 0% stop, the first color declared will be at that point. Similarly, the last color will continue to the 100% mark, or be at the 100% mark if no length has been declared on that last stop. <linear-gradient()> =
This example uses multi-position color stops, with adjacent colors having the same color stop value, creating a striped effect. How do you add a fade effect in CSS?In the CSS, use the @keyframes rule paired with fadeIn. At 0%, set the opacity to 0. At 100%, set the opacity to 1. This creates the fade-in effect.
How do I make a div appear slowly?$("div"). animate({ opacity:0 },"slow"); This is useful if you also want to animate other properties of the element at the same time.
How do you fade edges in CSS?To feather the edges of an image using CSS, you can use the box-shadow property. You can set the box-shadow property to create a soft, blurred shadow around the image. For example: This will create a shadow around the image with a blur radius of 5px and an opacity of 50%.
How do I fade text left to right in CSS?To create a animation that fades in from left to to right we need to update our CSS to:. transform: translate3d(-50px, 0, 0); - move the element to the left as the initial state.. on hover, we move it to the right with transform: translate3d(0, 0, 0); - eg moving from -50px to 0.. |